Leaderboard

HI, first thank you very much for this piece of art! after a few flights I have some suggestions to make the experience even better. 1. The checklist It works great, but I fly a lot of legs right after one another and I guess some checklist items are skipped in the second (or later) flight. RIght now I have to go through all of the items again, which takes a lot of time. Maybe You could add an option for starting the first checklist of the day and a separate for a shortened one for the second and following flights. Also, it would be nice to hear the FO reading the checklist through my headset, separated from the engine/environment sound which comes through my speakers. Sometimes it is quite hard to hear my FO. 2. The status of the pushbuttons Not really your problem, but recognizing whether a pushbutton is pushed in or out, especially at night, is quite hard to see on a monitor (for example the stab trim channels). Right now the mouse pointer already changes from the normal shape to a hand when you hover over the pushbuttons to interact with them. Maybe a small symbol could be added to indicate whether the next mouse click pushes the button in or out. Thank you very much! kind regards chris

Thanks for sharing your deeply knowledgeable insight Oliver, Not being a corporate pilot, I didn't realize that in the real thing the pilot had to get out of his seat, head over to the touch screen panel above the sink, press an announcement button, and then head back to his seat each time. But now I know ;-)

I just imagine the pilot and the fueler fighting over the fuel port door. Fueler opens it and walks back to the truck, the pilot closes the door and walks away, the fueler looks back and sees it closed, and walks back over to open it. Rinse and repeat. Fueler radios into base, "the door on the fuel port of this challenger wont stay open, it's like it's spring loaded!" Let the fueler do his job, he'll close the door when he's done!

I'm at 2 days and counting. Still haven't left the ground. My baseline time will leave plenty of room for improvement.

You could be a little more appreciative of the time @Graeme_77 has put forward to try and help you learn this product...free of charge on his behalf. There is not likely to be something like an FCOM found with a real aircraft. Bombardier owns this material and sells it for thousands of dollars, or included with a $30 million purchase. We are not authorized to re-distribute this at all. It's 7,000 pages too, by the way. Along with @Graeme_77, there is also several video series of operating the aircraft complete with explanations by @skiselkov. Most customers have taken to this to learn the product and get along quite well. I do not expect anyone to understand everything here in a day, but exploring and learning through watching the series is rewarding. This is the answer we are able to give you now. Your impatience is evident, so there's your "right now" answer. I have never once looked through any manual for any car I have bought. This is probably not a great example. Ironically for things like this I'd default to YouTube, of which there's also a ton of livestream content to soak in as well for the 650. @Graeme_77 is a volunteer of his time. Please be respectful of his willingness to assist you considering he is not officially a Hot Start developer. He's an extremely knowledgable, kind person who is trying to help you and was gracious enough to help beta test this product before it went to market. He receives no money from this product. There's enough info in this thread to lock it for the time being. Please, use the free training videos out there at your leisure and learn best you can. If you are unable to make sense of something, post here and any of us will be happy to further explain things to you short of sending you thousands of dollars worth of copyrighted Bombardier manuals.

I was testing having 1 airframe for FSE, 1 airframe for non-FSE but persistent location, then 1 airframe for freedom of location, but persistent with the airframe. Steps To Reproduce: Create an airframe in career mode. Fly that airframe somewhere. Close simulator and reopen (simulate a second date of flight). Upon loading into the sim, choose a different airport. Start flight and get into the Hotstart menu, I clicked on career mode Selected the same airframe and unchecked "Restore Previous Position". Clicked Enter FBO and loaded in. All was well.. it will load the new location but not all is well, at least when I went to the plane. I went to the plane, clicked on the door handle to pop open the square and nothing but the sound happened. Clicked it a few more times, nothing. I hit Shift + 4 which took me inside the plane, stood up and walked to the door. I could pull on the small handle in the center, but the big handle on the side was not working. Video Showing the Issue: Apologies for the fan in background, new headset and hadn't realized it was doing that. CL650_Logs.zip

Apologies, if this has been asked and answered somewhere before, but is it possible to have the cabin announcements automate? It would be a ton more immersive if it was triggered somehow. Thanks so much Len

It looks like Alaska may be being seen as part of Canada by the fueler. Specific gravity provided in kilograms and quantity is in liters.

I checked with one of the other pilot client devs (swift) and they derive pressure alt from true alt using local sea level pressure. That's probably what xPilot should do too, to be compliant with the spec and provide more realistic behavior. I've asked Justin about it.

Now this made me laugh! made my day.

Seems possible. One cumbersome but hopefully reliable way to check it might be to try and enter the route manually in the Challenger (or even the default FMS) and see if any waypoints are missing or if there are airway mismatch errors, for example. If there is, then there's no easy way to fix it other than to redispatch with a route that works for both cycles (e.g. replacing any missing fixes, maybe by lat/long coordinates, and replacing airways by directs, that sort of thing). I suppose, generally, always replacing every airway by directs (adding all or some intermediate fixes manually, for example when the airway changes course) is a good idea when your Simbrief and simulator cycles differ. One solution commonly employed is for people to buy one month of Navigraph Ultimate, which lets you update both SimBrief and your aircraft so their cycles match (don't forget to backup your Custom Data folder as well as any folders for aircraft where the navdata is located elsewhere), then cancel their subscription so it doesn't renew. SimBrief will allow you to use your old dataset forever (as of a few years ago), though some people like to repeat the procedure every year so as to keep their navigation database reasonably recent. Regards, Tim

It worked thanks for the help

Some switches are latching, some are not. The stab trim switches, Mach trim and yaw damper switches are momentary contact types - they are spring loaded to the “up” position. The only way to tell if the stab channels and yaw dampers have been engaged is to monitor the EICAS. For some reason Bombardier decided to put a light in the Mach trim, but not the others. Most of the overhead panel switches are latching (with status lights), but not all. On the CRJ-200, the 14th stage bleed air switches are lit when disengaged (even if the engine is shut down), while on the 605 the lights only become active after engine start, though it actually has no adverse effect during engine start even if they are left engaged. The APU master switch has no status light in the real airplane or in the sim. That is one that would benefit from a tooltip to indicate if it is pressed or not. The external power switch is another one that would benefit from a tooltip, as it is easy to leave it accidentally pressed in after the APU is started and the GPU is disconnected.

When a cabin attendant is not onboard the pilots have a version of the panel on their iPads hooked into the cabin WiFi. For now this can be emulated by using the pop up, available via key bind.

If you want you could bind that panel to a button on your keyboard. I’m not sure how exactly the binding was named, but it is available under the aircraft-specific keys. Just give it a try. It helps a lot.

Hello, Navigate to your LEGS page and locate the waypoint which has had a constraint applied. Input the required level into the scratchpad and use the appropriate right side LSK (line select key) to transfer the information from the scratchpad. Some additional information below that you may find useful: - To enter an altitude simply input "6000" or "12000". To enter a flight level input "F310" or "FL310" - If you're given an "at or above" put "A" afterwards, eg. "6000A". - If you're given an "at or below" put "B" afterwards, eg. "F270B" - If you're given a "between" enter the lower altitude, then "A", then the upper altitude and "B" - eg. "7000A9000B" - You can also input a speed restriction at the same time, eg. "250/10000" or "220/5000" using the forward slash to separate.

Hi, the right hand side is reading 2992 and is in negative numbers but the 2992 can be changed. The pilot side is 9000 feet but the baro cannot be changed the needle swings wildly then goes back to where it was. I will try removing the plugins next. Thanks for your prompt reply, regards Ian.

I'll put this one in the "I'll consider it" tray. Only reason being is because it is a 604/605 variant. I do like it, though.

We're going to research the amount of wing flex before adding it, if there is any.

Is this much analysis into wing flex really necessary? they're a small wing, they wont bend that much anyway. i offer in exchange - actual wing flex

Unfortunately that may be an error in the document (we are checking), of the two I know that Fin Number is supported. The location in Simbrief is highlighted in the primer document. It may or may not be part of the OFP format you use. That’s up to you, but it’s not necessary if everything is working correctly with the uplink. If you mean in Simbrief, then no.

This specific issue has been fixed by the developer and will come with the first update. Thanks for helping improve the product!

Good day, thank you again for this airplane. It is the best! Here is my log Thanks Log.txt

It looks like there could be some improvements possible with temperatures and persistence. The developers and testers are aware and will investigate further. Thanks for the report.

IIRC the FMS will update automatically, so it’s just a case of winding the altitude up, FLC mode and you’ll be fine. If you need to nudge the mach number back a tiny bit to help it climb that’s fine, but if a bigger change than 0.02 mach is needed then you’re probably asking it to fly a bit too high. There are limiting weights for cruise levels shown in the Ops Reference manual, and I’ve found the SimBrief step climbs to be pretty accurate too. I don’t know the best way to get fuel predictions including a future step, so will do some investigation when I get a chance.

I have HDR enabled and the above person is correct the Nose light does not cast light.

Yes, any time you have to leave and re-enter VR it's like playing roulette as to whether or not X-Plane will crash.

Fixed, will be in next update.

Zero tests. The aircraft is completely cold & dark, no de-icing required. I am using the FBO fueling process, it's actually faster than the manual process because it's synchronous. I put on ~ 3000 lbs. of fuel and gave myself 5 minutes on "when are you leaving" phase of the FBO experience. The IRS alignment process is 6-minutes, so that's about as fast as you'll ever go through a legitimate take off sequence. In my case, I was 100% ready to go at 6-minutes. Like engines running, door closed, passengers seated. Truthfully, a normal flow for me is 12 to 15 minutes. But I tried a "speed run" to see how fast I could theoretically get off the ground.

View File Hot Start - Challenger 650 - Jetflite livery Jeflite livery for the Hotstart CL650. Registration used is the OH-WIW, but can be easily modified with the airframe manager to match the OH-WIC. Enjoy ! Submitter Meilstroms Submitted 01/14/2022 Category Hot Start Challenger 650 Livery For https://www.x-aviation.com/catalog/product_info.php/take-command-hot-start-challenger-650-p-212  

She’s working from home - covid!

This is indeed normal. The reason is quite simple: the ATS needs an N1 limit target to operate. Otherwise, it would have no idea what the maximum allowable thrust is. This value is supplied by the FMC. The FMC uses performance tables made by the aircraft manufacturer to determine what the takeoff thrust limit is supposed to be and if I show what the table looks like, you'll immediately see the source of the problem: Your SAT is +35 C. At that temperature, the FMC has no data to compute a takeoff N1 target, so the target blanks and the ATS goes to FAIL (and cannot be re-engaged). Take the cowl A/I off, FMC goes back to the normal takeoff tables and voila, ATS is back in business.

If HotStart has such data and can share it, it would be helpful to have that larger dataset shipped with the addon or maybe just available here in the forums. It does not necessarily have to be converted into a ready-to-use PFPX profile by HotStart but unless the community gets access to such data (as a spreadsheet table, PDF, text file, whatever format) it's impossible for anybody to write such a file. I didn't try to feed the very short and limited dataset that currently comes with the documentation into a PFPX profile as (having seen tables from airliner FCOMs where performance data is provided on several pages) I suspect that data is way to limited to end up with some reasonable results in PFPX.

Ok found it. On the CDU: TUNE and then click on the squawk code with nothing in the scratchpad. Test is on the upper right of the page.

FWIW, the same altitude discrepancy issue exists for users of Pilot2ATC, not just vatsim and pilotedge. Would be great to have a way to handle for those users as well as true online networks.

Yes indeed. Will be fixed, sorry for not spotting that before release.

Is this the new "my ashtray is full, i need to buy a new car"? Bloody throwaway society...

Personal I do export it with LNM as fms at X-Plane/Output/FMS plans/ and load it in CL650 via IDX(index) > ROUTEMENU > DISK ROUTE LIST > navigate to correct with PREV & NEXT and pressing appropriate Left LSK The same you can do with every third party flight planner. Hope that this help you.

For some odd reason they got deleted by youtube...and I don´t have them anymore . I plan on redoing them with XP12 when that one comes out - there have been a lot of changes to our model since back then and also the new simulator platform warrants a better looking video, so might as well redo them then! Cheers, Jan

LINK HERE Note: aircraft name is clipped to 12 characters for custom airframes, sadly (limit does not apply to default profiles). Fixed by SimBrief Based on the already-accurate default CL60, with the following adjustments: equipment codes and extra flight plan remarks kindly provided by Graeme_77 here: OEW/BOW updated to match the Hot Start airframe without passengers (12,315 -> 12,556kg, includes two pilots) passenger weights updated to somewhat more closely match the randomized weights as simulated, going with 74+15kg so you can still carry 5 passengers+luggage and full fuel at MTOW if you are flying Kim Dotcom around (supposedly ~141kg or thereabouts), sorry, you will have to make adjustments, or just count him as two passengers see below for more information: Don't forget to add extra crew (anything above the two included in OEW) as passengers when planning your flight! Cheers, Tim

I have a small thing to add... The switches of the refueling panel are so black, I cant see which position they are... Only when i look from near 90 deg from the side.

Redownload the installer from X-Aviation website. Your liveries, settings and save states will persist. Brgds

Hey N1k, There's no defuelling capability, Toto felt it wasn't worth implementing, as it's extremely rare that you can defuel an aircraft. No one would be willing to accept the fuel from your tanks due to the potential of contamination. If you've put too much fuel in your aircraft, and can't take-off (short runway for example), then you're just gonna have to sit on the tarmac and burn it.