Leaderboard

TBH, we can't fully blame them (I'm one of them with the MU2) ....we've been 'crossing our fingers' for a while that XP12 doesn't break our radar display....and the spectre of such still exists. Its like two people walking towards each other and that awkard moment where neither is sure which way the other one will move and you kind of stutter-step....a lot of devs and Laminar are doing that right now IMO. We've gotten lucky in a way that we haven't had to do a darn thing to 'get around' the new weather system..we happen to select a method that has held up thus far..but it is based on the previous weather system pardigm....and as such, we are always 'looking over our shoulder' at it so to say, in case is sneaks up on us one day All that said...I do think the time is coming where it needs to be addressed. There is a XPlane developer conference in February and I suspect this will get discussed. -tk

CCP1 or 2

...there is no reason not to buy it. I will personally refund your money if you feel betrayed/disappointed

Pull down menu - Cl650 - Ground services - Restow ADG

I was going to post this same issue. When I first load a plane now that uses Gizmo (including the G500 on non X-Aviation planes) I get a huge cpu draw from Gizmo. My cpu frame time goes from 0.200 to 1.500 for a minute or so. Eventually it settles down and Gizmo shows about 0.10% usage in the admin window. But then every minute or two it goes back up to 50% usage for a few seconds before settling back down which causes stutters. I've tried this with the 737, Mu2, BN-2T and the Laminar 172 with G500. I bought both the 737 and the G500 at the same time so not sure which one triggered it. My system is old, i7 4790 and I have a 5800X3D build I'm completing tomorrow so I'll report back if it continues with that new system. Prior to this week I never had an issue with Gizmo so did something update it on the 737 or G500 purchases? Btw my tests were done at various locations including Land's End which is usually very light (I get 60fps in the stock 172) just to rule out scenery problems.

That caught me off guard, hahaha..

Hi Steve, When you are happy with the state of the plane, save the state. You can even save a state after each step, and restart frome here. If you start from a different airport, untick "Restore position and trajectory".

Well, it's the right place to post when it comes to the Challenger. It would help us to help you if you outlined the steps you did to achieve this. Sometimes, a step or 2 can be missed, even when following an instructional video. There's a shutdown checklist. But as a last resort, have you tried creating a new airframe? Why? You can leave it installed, and then come back to it. There's no reason to uninstall. This is a hobby, Stefan. Try to treat it as such. Set aside a block of time where you can try to enjoy it. If help is needed, we're a few keystrokes away. There are many videos that go over many different areas of this add on. Particularly from Reflected Reality Simulations. Very highly recommended. The product page is very clear with regards to the complexity of this add on. It's not a difficult add on to get into, but it is complex and extremely detailed. If it's going to get you this frustrated or annoyed, I suggest you take a small break and come back. There are many people willing to help you overcome any obstacles.

It looks like the cockpit door is open in your picture? If it isn´t, then the camera position should govern it - we have to "fake" the cockpit door blocking the light because the lighting engine in X-plane does not allow solid structures blocking any light besides the sun (and even that not always). So we "fake" the door blocking the light by checking wether the camera is in the cockpit AND the cockpit door is closed. If this is TRUE, we turn off the galley light (even though the switch is actually ON). But if you move the camera out of the cockpit (like in your screenshot), the light goes back on and will illuminate the cockpit a little bit.

Enable random failures for HotStart Challenger 650 View File This LUA script enables random failures for the HotStart Challenger 650. Requirement: The script requires FlyWithLua: Download the correct version for your simulator. FlyWithLua for X-Plane 11: - https://forums.x-plane.org/index.php?/files/file/38445-flywithlua-ng-next-generation-edition-for-x-plane-11-win-lin-mac/ FlyWithLua for X-Plane 12: - https://forums.x-plane.org/index.php?/files/file/82888-flywithlua-ng-next-generation-plus-edition-for-x-plane-12-win-lin-mac/ Installation: - Unzip the files in [X-Plane]\Resources\plugins\FlyWithLua\Scripts Settings: (edit the lua script) -- Here you set if the failures should be default enabled or disabled when your starting up X-Plane. -- You can also enable and disable this option (for the current session) in the FlyWithLua menu. -- Set true to enable failures, false to disable. Default is true. true and false have to be written with lowercase letters. EnableFailures_WizVar = true -- Mean time between failures (MTBF) is the predicted elapsed time between inherent failures of a system during operation. -- Default is MTBF_hours = 10.0 local MTBF_hours = 10.0 -- Max failures pr session -- Default is Max_Failures = 2 local Max_Failures = 2 -- Severity 1 to 5. 1 least severe, 5 most severe. i.e. if you select 3, you will get failures from severity 1 to 3. local Severity = 5 -- Clear all failures when starting x-plane. Default is false. true and false have to be written with lowercase letters. local ClearAllFailures = false MTBF: This graph shows a example how often you can expect a failure when you set the MTBF to 10 hours. Failures included in the script: CL650/failures/systems/ats/failed/state Auto Throttle System has failed CL650/failures/systems/ats/msd/1/failed/state Left ATS MSD has failed CL650/failures/systems/ats/msd/2/failed/state Right ATS MSD has failed CL650/failures/systems/afcs/yd/1/failed/state Yaw Damper Channel 1 has failed CL650/failures/systems/afcs/yd/2/failed/state Yaw Damper Channel 2 has failed CL650/failures/systems/elec/comp/HTR_L_WSHLD_1/failed/state Left windshield heater 1 has failed CL650/failures/systems/elec/comp/HTR_L_WSHLD_2/failed/state Left windshield heater 2 has failed CL650/failures/systems/elec/comp/R_WSHLD_1/failed/state R windshield heater 1 has failed CL650/failures/systems/elec/comp/R_WSHLD_2/failed/state R windshield heater 2 has failed CL650/failures/systems/elec/comp/HTR_R_WIND/failed/state Right window heater has failed CL650/failures/systems/elec/comp/CABIN_TEMP_SENSE/failed/state Cabin temperature sensor has failed CL650/failures/systems/elec/comp/LDG_TAXI_LTS_R_NOSE/failed/state Right nose LDG-taxi lights has failed CL650/failures/systems/elec/comp/LDG_TAXI_LTS_R_WING/failed/state Right wing LDG-taxi lights has failed CL650/failures/systems/elec/comp/HTR_L_WIND/failed/state Left window heater has failed CL650/failures/systems/elec/comp/ANTI_SKID_1/failed/state Anti-skid 1 has failed CL650/failures/systems/elec/comp/AUTO_THROTTLE/failed/state Autothrottle has failed CL650/failures/systems/elec/comp/CABIN_TEMP_CONT_AUTO/failed/state Cabin temp ctrl (auto) has failed CL650/failures/systems/elec/comp/ANTI_SKID_2/failed/state Anti-skid 2 has failed CL650/failures/systems/elec/comp/STAB_CH_1_HSTCU/failed/state Stab trim channel 1 ctrl has failed CL650/failures/systems/elec/comp/STAB_CH_2_HSTCU/failed/state Stab trim channel 2 controller has failed CL650/failures/systems/iceprot/wnd_heat/1/failed/state Left window heat has failed CL650/failures/systems/iceprot/wnd_heat/2/failed/state Left windshield heat has failed CL650/failures/systems/iceprot/wnd_heat/3/failed/state Right windshield heat has failed CL650/failures/systems/iceprot/wnd_heat/4/failed/state Right window heat has failed CL650/failures/env/birdstrike/strike/state Birdstrike that doesn't lead to any damage CL650/failures/env/smoke/baggage/state Smoke in the baggage bay CL650/failures/env/smoke/lavatory/state Smoke in the toilet CL650/failures/systems/elec/ac/gen/1/failed/state Generator 1 has failed CL650/failures/systems/elec/ac/gen/2/failed/state Generator 2 has failed CL650/failures/systems/elec/comp/HYD_PMP_3B/failed/state Hydraulic pump 3B has failed CL650/failures/systems/elec/comp/HYD_PMP_2B/failed/state Hydraulic pump 2B has failed CL650/failures/systems/elec/comp/HYD_PMP_3A/failed/state Hydraulic pump 3A has failed CL650/failures/systems/elec/comp/HYD_PMP_1B/failed/state Hydraulic pump 1B has failed CL650/failures/systems/elec/comp/FLAP_MOTOR_2/failed/state Flap motor 2 has failed CL650/failures/systems/elec/comp/FLAP_MOTOR_1/failed/state Flap motor 1 has failed CL650/failures/systems/elec/comp/HUD/failed/state Heads Up Display has failed CL650/failures/systems/hyd/1/pump/A/state Engine-driven pump 1A has failed CL650/failures/systems/hyd/1/pump/B/state AC electric pump 1B has failed CL650/failures/systems/hyd/2/pump/A/state Engine-driven pump 2A has failed CL650/failures/systems/hyd/2/pump/B/state AC electric pump 2B has failed CL650/failures/systems/hyd/3/pump/A/state AC electric pump 3A has failed CL650/failures/systems/hyd/3/pump/B/state AC electric pump 3B has failed CL650/failures/sensors/ads/pitot/3/leak_small/state Standby pitot tube is leaking pressure (inaccurate speed reading) CL650/failures/avionics/efis/hud/failed/state Heads Up Display has failed CL650/failures/systems/eng/left/compr/stall/trans/state Left engine compressor stall (transient, self-clearing) CL650/failures/systems/eng/right/compr/stall/trans/state Right engine compressor stall (transient, self-clearing) CL650/failures/systems/eng/left/oil/pump/weak/state Left engine oil pump is producing low pressure and low flow CL650/failures/systems/eng/right/oil/pump/weak/state Right engine oil pump is producing low pressure and low flow CL650/failures/env/birdstrike/windshield/state Birdstrike that leads to the left windshield's outer pane shattering CL650/failures/systems/aircond/leak/500/state Cabin is leaking pressure at ~500 ft/min CL650/failures/systems/comm/sdu/1/failed/state Satellite Data Unit 1 has failed CL650/failures/systems/comm/sdu/2/failed/state Satellite Data Unit 2 has failed CL650/failures/systems/fuel/tank/aux/leak/slow/state Auxiliary tank is leaking slowly CL650/failures/systems/fuel/tank/main/left/leak/slow/state Left main tank is leaking slowly CL650/failures/systems/fuel/tank/main/right/leak/slow/state Right main tank is leaking slowly CL650/failures/systems/fuel/tank/tail/leak/slow/state Tail tank system is leaking slowly CL650/failures/systems/hyd/1/leak_slow/state Hydraulic system 1 is leaking slowly CL650/failures/systems/hyd/2/leak_slow/state Hydraulic system 2 is leaking slowly CL650/failures/systems/hyd/3/leak_slow/state Hydraulic system 3 is leaking slowly CL650/failures/sensors/ads/pitot/1/leak_small/state ADC 1 pitot tube is leaking pressure (inaccurate speed reading) CL650/failures/sensors/ads/pitot/2/leak_small/state ADC 2 pitot tube is leaking pressure (inaccurate speed reading) CL650/failures/avionics/efis/pfd/1/failed/state PFD 1 has failed CL650/failures/avionics/efis/mfd/1/failed/state MFD 1 has failed CL650/failures/avionics/efis/mfd/2/failed/state MFD 2 has failed CL650/failures/avionics/efis/pfd/2/failed/state PFD 2 has failed CL650/failures/avionics/efis/isi/failed/state ISI has failed CL650/failures/avionics/efis/isi/pitot/state ISI pitot sensor has failed CL650/failures/avionics/efis/isi/static/state ISI static sensor has failed CL650/failures/avionics/efis/isi/att_fail/state ISI attitude indication has failed CL650/failures/avionics/efis/isi/att_drift/state ISI attitude indication is drifting randomly CL650/failures/systems/oxygen/tank/leak/slow/state Oxygen tank is leaking slowly CL650/failures/systems/eng/left/n1_vib_high/state Left engine is experiencing excessive N1 vibration CL650/failures/systems/eng/left/n2_vib_high/state Left engine is experiencing excessive N2 vibration CL650/failures/systems/eng/left/combust/flameout/trans/state Left engine combustion has flamed out (momentarily) CL650/failures/systems/eng/right/n1_vib_high/state Right engine is experiencing excessive N1 vibration CL650/failures/systems/eng/right/n2_vib_high/state Right engine is experiencing excessive N2 vibration CL650/failures/systems/eng/right/combust/flameout/trans/state Right engine combustion has flamed out (momentarily) CL650/failures/systems/aircond/leak/1000/state Cabin is leaking pressure at ~1000 ft/min CL650/failures/systems/ats/svo/1/failed/state Left ATS Servo has failed CL650/failures/systems/ats/svo/2/failed/state Right ATS Servo has failed CL650/failures/systems/elec/comp/FMS_CDU_2/failed/state CDU 2 has failed CL650/failures/systems/elec/comp/FMS_CDU_3/failed/state CDU 3 has failed CL650/failures/systems/elec/comp/FMS_CDU_1/failed/state CDU 1 has failed CL650/failures/systems/fuel/tank/aux/leak/fast/state Auxiliary tank is leaking quickly CL650/failures/systems/fuel/tank/main/left/leak/fast/state Left main tank is leaking quickly CL650/failures/systems/fuel/tank/main/right/leak/fast/state Right main tank is leaking quickly CL650/failures/systems/fuel/tank/tail/leak/fast/state Tail tank system is leaking quickly CL650/failures/systems/hyd/1/leak_fast/state Hydraulic system 1 is leaking quickly CL650/failures/systems/hyd/2/leak_fast/state Hydraulic system 2 is leaking quickly CL650/failures/systems/hyd/3/leak_fast/state Hydraulic system 3 is leaking quickly CL650/failures/systems/oxygen/tank/leak/fast/state Oxygen tank is leaking quickly CL650/failures/systems/eng/left/compr/stall/clear/state Left engine compressor stall (clearable by reducing power) CL650/failures/systems/eng/right/compr/stall/clear/state Right engine compressor stall (clearable by reducing power) CL650/failures/env/birdstrike/pitot/left/state Birdstrike that leads to the left pitot tube becoming blocked CL650/failures/env/birdstrike/pitot/right/state Birdstrike that leads to the right pitot tube becoming blocked CL650/failures/systems/aircond/leak/fast/state Cabin is leaking pressure quickly CL650/failures/systems/gear/handle/failed/state Landing gear handle failed CL650/failures/systems/gear/nose/leg/act/failed/state Nose gear leg actuator has failed CL650/failures/systems/gear/main/left/leg/act/failed/state Left gear leg actuator has failed CL650/failures/systems/gear/main/right/leg/act/failed/state Right gear leg actuator has failed CL650/failures/sensors/rss/gps/1/failed/state GPS 1 receiver has failed CL650/failures/sensors/rss/gps/2/failed/state GPS 2 receiver has failed CL650/failures/systems/eng/left/combust/flameout/perm/state Left engine combustion has flamed out (permanently) CL650/failures/systems/eng/right/combust/flameout/perm/state Right engine combustion has flamed out (permanently) CL650/failures/env/birdstrike/eng/left/state Birdstrike that leads to a non-recoverable left engine failure CL650/failures/env/birdstrike/eng/right/state Birdstrike that leads to a non-recoverable right engine failure Submitter Tom Stian Submitted 08/14/2023 Category Plugins and Utilities  

Too easy! Anybody with access to the 717 willing to help..or a friend of a friend of a friend with access.....please hit me up in PM. This is well into late 2024 at best...737 comes first so i won't talk 717 much. Its just out there waiting its turn....but I reserve the right to work on it nights/weekends It doesn't quite work that way...besides, interior mostly done anyhow. The 'standard' is the standard. Immersion is a huge part of the product and many customers enjoy it all around. Lots of folks like replay mode from the cabin etc. Once this interior is done, I won't have to worry about it and can get back to the FMS and such. -tkyler