wain Posted May 31, 2017 Report Posted May 31, 2017 13 hours ago, Litjan said: I trust that you applied the manual fixes to the .acf file that is required for the APU to work in XP11? @Litjan it was my error, all working perfectly now....thanks... 1
mga010 Posted June 1, 2017 Report Posted June 1, 2017 I have only X Plane 11 installed right now. I think it is far superior to X Plane 10 in so many areas that I ignore the areas were it is a step back. So I would very much like to have a reliable 737 that works as I expect, even in non-standard procedures. I also noticed the strange behavior while taxiing (in part due to the exaggerated slopes on taxi paths in some airports of X Plane 11). There is also quite a lot asymmetrical engine spool-up after the fix above, more than is realistic. After takeoff there is a problem with the lift close to the ground. And flaring is not quite realistic. But overall, I find this quite enjoyable. So, please go ahead and work on the X Plane 11 version if possible. Paul
Morten Posted June 1, 2017 Report Posted June 1, 2017 Well, as you just noted yourself, XP11 still has it's flight model problems as well Not all your observations are correct, but we have come a long way on the XP11 update and once the v1.1 release dust has settled work will continue. 2
aluisioacabral Posted June 7, 2017 Report Posted June 7, 2017 Hello guys I wanted to know if its possible to fix the problem in my 737 ixeg presents in x-plane11. The problem is any thing that i will change during my fight fmc of 737 ixeg the aircraft starts to lock and only unlock when I press execute (exec) in fmc
Tom Stian Posted June 7, 2017 Report Posted June 7, 2017 1 minute ago, aluisioacabral said: Hello guys I wanted to know if its possible to fix the problem in my 737 ixeg presents in x-plane11. The problem is any thing that i will change during my fight fmc of 737 ixeg the aircraft starts to lock and only unlock when I press execute (exec) in fmc Hello sir, Take a look here.
aluisioacabral Posted June 7, 2017 Report Posted June 7, 2017 10 minutes ago, Tom Stian said: Hello sir, Take a look here. Thank you very much
awilks01 Posted June 10, 2017 Report Posted June 10, 2017 (edited) Hey Guys-- I got the aircraft working in XP11, and all is well, except when I start the engines, and get the ac ready for taxi, and advance my throttles, the two throttles move forward, but only one engine spools up respectively, if that makes sense. As power is added, only one advances, the other stays at idle, even though the throttles are both moving together. Sorry, it's a confusing problem. Just wondering if anyone found a fix for it via planemaker or anything else. I know the aircraft is not fully XP11 compatible, but one can hope for a jerry rigged fix for this issue, right? IXEG, you did a marvelous job on this bird, take all the time you need to get the Xp11 patch out. I read a lot of negativity about this, hopefully this positivity shines a little bit of light for you all. IXEG 1.1 Edited June 10, 2017 by awilks01 1
Litjan Posted June 10, 2017 Report Posted June 10, 2017 2 minutes ago, awilks01 said: Hey Guys-- I got the aircraft working in XP11, and all is well, except when I start the engines, and get the ac ready for taxi, and advance my throttles, the two throttles move forward, but only one engine spools up respectively, if that makes sense. As power is added, only one advances, the other stays at idle, even though the throttles are both moving together. Sorry, it's a confusing problem. Just wondering if anyone found a fix for it via planemaker or anything else. I know the aircraft is not fully XP11 compatible, but one can hope for a jerry rigged fix for this issue, right? IXEG, you did a marvelous job on this bird, take all the time you need to get the Xp11 patch out. I read a lot of negativity about this, hopefully this positivity shines a little bit of light for you all. Hi and thanks for the nice words. If you post in this thread, which is aptly named "ixeg-737-in-x-plane-11-how-to-get-it-work", I trust that you have read the first post and followed the instructions given there? Just want to make sure before I spend the time to dive deeper into the problem you still seem to be having. Cheers, Jan
awilks01 Posted June 10, 2017 Report Posted June 10, 2017 1 hour ago, Litjan said: Hi and thanks for the nice words. If you post in this thread, which is aptly named "ixeg-737-in-x-plane-11-how-to-get-it-work", I trust that you have read the first post and followed the instructions given there? Just want to make sure before I spend the time to dive deeper into the problem you still seem to be having. Cheers, Jan Hi Jan, I have taken the steps outlined in the first post Austin
Litjan Posted June 10, 2017 Report Posted June 10, 2017 Hi Austin, that is really odd - usually this happens when the "idle values" are not adjusted via planemaker - the engines idle so low then, that advancing the throttle is just "choking" them and they won´t rev up. Can you post a screenshots of your enigine instruments at idle thrust, please? Thanks, Jan
Whiskey Rebel Posted June 10, 2017 Report Posted June 10, 2017 This was happening to me too (under XP11/737C-10.7). When I reset by way of Pre-Flight Options it would be okay. However I have not had the problem since v1.1 and followed the instructions that Jan referred to.
awilks01 Posted June 10, 2017 Report Posted June 10, 2017 4 hours ago, Litjan said: Hi Austin, that is really odd - usually this happens when the "idle values" are not adjusted via planemaker - the engines idle so low then, that advancing the throttle is just "choking" them and they won´t rev up. Can you post a screenshots of your enigine instruments at idle thrust, please? Thanks, Jan Here you go, Jan Austin
mmerelles Posted June 10, 2017 Report Posted June 10, 2017 (edited) 18 minutes ago, awilks01 said: Here you go, Jan Austin Austin, as per your screen capture it seems the engine adjustments required on planemaker were not made. The aircraft idle is too low N1 % is 11 should be around 21 can you open planemaker again and confirm: -you did not configure another field? -were both values set hi & lo? -make sure you save the changes via planemaker menu before you exit. hope this helps Edited June 10, 2017 by mmerelles 1
awilks01 Posted June 11, 2017 Report Posted June 11, 2017 Well, it appears I put the values in the incorrect spaces. My bad guys.
XXFlight Posted June 11, 2017 Report Posted June 11, 2017 (edited) I recommend adjusting hi idle to 1.18 and lo idle to 0.61 so as to not have so much push on the ground roll. This will leave N1 idle at 21.6/7 and will not push N2 past 100% on the climb. Edited June 11, 2017 by XXFlight
mishaikin Posted June 12, 2017 Report Posted June 12, 2017 Hi Austin, that is really odd - usually this happens when the "idle values" are not adjusted via planemaker - the engines idle so low then, that advancing the throttle is just "choking" them and they won´t rev up. Can you post a screenshots of your enigine instruments at idle thrust, please? Thanks, Jan Hi Ian, I noticed the same issue with "choking" while taxiing after landing in XP10, so maybe this is not XP11 specific problem. I even have a video on twitch. Sent from my VKY-L29 using Tapatalk
PilotNL Posted July 10, 2017 Report Posted July 10, 2017 (edited) Works like a charm! Many thanks! Perhaps one minor issue, not sure if this is xpx11 related or if it was already like this in xp10: I have the fuel setup in kg. in the PERF page I can setup the amount in kg (tonnes). the totalizer is also in KG as are the gauges on the main panel. In the PROGRESS page, FROM waypoint is als in KG, however, the next waypoints and the destination show in LBS... Anyone else seeing this? Edited July 10, 2017 by PilotNL
mmerelles Posted July 10, 2017 Report Posted July 10, 2017 PROG page is not working yet, under development. Do not use it. 1
Freight Dawg Posted July 11, 2017 Report Posted July 11, 2017 10 hours ago, mmerelles said: PROG page is not working yet, under development. Do not use it. No "Des Now" either? thx
mokny Posted July 11, 2017 Report Posted July 11, 2017 1 hour ago, Hammer32261 said: No "Des Now" either? thx You nailed it 1
Recommended Posts