Real Life CL650 pictures

KirkR · August 16, 2022

Fantastic. Thanks for posting these. I would be happy to convert your photos to JPEG, could provide a Dropbox to post them into. Don't hesitate to ask.

KirkR · August 17, 2022

Yep, times have changed. Permanent no smoking on board.

FYG001 · August 18, 2022

Switch has been removed, position OFF, ie no smoking sign is off

FYG001 · August 18, 2022

A few more for today

FYG001 · August 18, 2022

KirkR · August 18, 2022

Question about end of the day checklist when you are going to leave the aircraft overnight. Do you install all five pins (3 nose wheel / chamber, 1 each main gear), and at what point do you do that in the checklist/process?

I assume that with a FO plus ground crew, it's not the process of going out and then back in like it is for the simulation (due to one pilot).

VictoryAJ · August 19, 2022

Every operation will be somewhat different of course....

Once we complete the last leg of the day and the shutdown check is complete, one of us is immediately getting up out of the seat to open the cabin door and go verify chocks are in place, the nose doors are opened, and 5 pins are inserted.

Of course if our last leg is a passenger leg - they are disembarked first. One pilot typically stays with them for the walk to the vehicles or the FBO - while the other pilot heads to the interior of the baggage compartment to pass the bags to line crew. That pilot then comes through the cabin to check for forgotten personal items - concluding with a thumbs up to the pilot adjacent the vehicles. If they walked inside - typically a text is sent between pilots that the cabin is clear (or isn't). At this point the pilot with the airplane will coordinate with the line crew re: required services - verifying chocks are in place - then retrieving the pins and inserting them.

Different operations have different philosophies/standards regarding nose doors opened or closed. At our home base - we will always open the doors and insert 5 pins. Away from home while on the road we can exercise discretion to leave them closed. In a location with security concerns, or if there are any concerns regarding tugs, line crew, etc - we may elect to go with 3 pins and leave the doors closed. I'd say in our operation the doors are left open with 5 pins the majority of the time. Under no circumstance will we leave the nose doors open without inserting the 2 additional pins.

Once pins are inserted and we're both back on the jet - it's time to start cleaning up and preparing for the next flight. Garbage is gathered, old coffee is dumped, drinks in the drawer with paper labels are removed from the ice bins - leftover catering is emptied from the chiller and either given to line crew as trash, as a gift, or to be stored in the FBO fridge. If the cabin needs to be vacuumed - we vacuum while power is still on. Tables and surfaces are cleaned at this point, seatbelts are cleaned and put back into presentation , the sinks and lav are cleaned and while this is happening - line crew is probably performing the lav service. Dishes and linens are given to line service as well. We like to keep power on until all of that is finished so we can check the lav - that enough (hopefully clean) water has been put back in and its back to smelling/looking fresh. We also have to restock from the storage drawers in back. Things like snacks, drinks, chips etc - all have to be replenished. If 15 minutes has gone by - one pilot is checking/servicing the oils in the utility bay. If temps will dip towards or below freezing - we purge the potable water system. This is often done at TOD depending on circumstances to avoid dumping 10 gallons of potable water on an FBO ramp which will turn into an iceberg. Water lines must be purged on the ground which is similar to prepping a recreational vehicle or boat for winter storage , minus the antifreeze, although there's different techniques there too.

Sometimes during all of this we may also fuel for the next day's flight - circumstances of course dictate when we would do this as there are considerations to keep in mind leaving the jet with a lot of fuel.

We also will consolidate crew baggage and put it in the baggage door opening in preps for offloading. We ensure the garbage, catering, fridge items, etc - are indeed all off.

The parking brake at this point has probably long been released since chocks were verified - and the signs put in the cockpit windows indicating the jet is safe to tow. We verify one of us has recorded the 'numbers' from the FMS for the trip paperwork. (OFF/ON/FLIGHT times and OUT/IN Fuel) Suction cupped iPad mounts are removed from the windows, the Sentry is verified as off and packed up so it can be charged at the hotel if needed. If it was a night flight and next flight is day, and we're about to secure the airplane - lights will be brought back to a daytime config (full bright). If it's a hot and sunny location - cabin window shades are closed and cockpit reflective covers are put in place. We also have a pin to secure the emergency exit in the cabin that gets inserted. At this point we verify requested services have been received/completed and we check with the other crewmember or crewmembers that they are done with cabin power. From here one of us typically runs the securing checklist and shuts down the APU. But we aren't done yet.

Our bags get unloaded at this point and we build our 'pile'. All external panels are locked. A thorough post flight walk-around is completed, typically by both of us. Covers are put on all 3 pitots, both ice detectors, the AOA cone and both AOA vanes. Both batteries are disconnected. Whichever pilot didn't do the cockpit securing - must 'check switches' to make sure all is where it should be.

Now it is finally time to make sure everyone is 'done inside' and the door gets closed/locked - and now - we can walk into the FBO, or to our rental car which has been brought planeside. We check in at the CSR desk regardless - providing contact info, verifying the schedule and services requested. This is a great time to make sure we go over the 'stuff in the fridge, the lav service, hangar arrangements, etc etc'. Only after this is all done do we leave the airport and head to the hotel where the trip PIC does 'the paperwork' which in our operation is electronic and must be submitted in a reasonable amount of time after the flight.

At home base our operation has a cleaning service that will take care of many of the above tasks, and since another leg often isn't happening the next day - we're off the airplane pretty quickly.

Hope this helps understand some of the things that go into this side of the business. On an international arrival after a long day mid-trip- it wouldn't be uncommon for the crew to take 30-45 minutes to do all of the above correctly.

KirkR · August 19, 2022

No doubt, many other Sim pilots will appreciate the time you took to go through that detail, as much as I do. Thanks so much.

VictoryAJ · September 2, 2022

KirkR · September 2, 2022

Ok, to the subject of the HUD ... sometime it would be great to understand the scenarios where the HUD is of the greatest value to you, and the degree to which you use it, and scenarios where you raise it. The closest "document" I have found on this device is a similar one from Rockwell Collins on smartcockpits. Still in pursuit of the one for the Challenger 6xx, but I have it pretty much figured out now.

https://www.smartcockpit.com/aircraft-ressources/HGS_00_Pilots_Guide_CRJ_00.html

dlrk · September 2, 2022

On 8/18/2022 at 11:01 PM, VictoryAJ said:

Every operation will be somewhat different of course....

Any chance you'd be interested in posting what a typical flight day is like for ya?

FYG001 · September 21, 2022

The boys sent me some more today

FYG001 · September 29, 2022

Interesting picture of our Challenger working its way westbound to 45N050W battling against an unusual strong westerly, although not any longer visible here

Edited September 29, 2022 by FYG001

FYG001 · October 1, 2022

Another couple of nice ones of the HUD, two with EFVS

FYG001 · October 4, 2022

And a few more for today

Zhivko · March 31, 2023

Hi everyone, thank you for the great photos already uploaded.

I would like to arrange the pop out windows in some set up of monitors, so the experience is even more realistic. Can you help me with some basic dimensions of the PFD, MFD, FMS CDUs and the DCP and CCP panels? I can use centimeters or inches whatever is convenient for you. Thank you in advance!

ois650 · March 31, 2023

6 hours ago, Zhivko said:

Hi everyone, thank you for the great photos already uploaded.

I would like to arrange the pop out windows in some set up of monitors, so the experience is even more realistic. Can you help me with some basic dimensions of the PFD, MFD, FMS CDUs and the DCP and CCP panels? I can use centimeters or inches whatever is convenient for you. Thank you in advance!

You may find this thread useful, it doesn't have all the measurements but I'm sure OP will oblige