Suprex 1 Posted Tuesday at 02:27 PM Report Share Posted Tuesday at 02:27 PM I have a strange question for you: if I chose to place the Saab on one of these three airports (LFCI - LFCR - LFCK), X-Plane loading freezes on writing "Done with Pre-loading". This doesn't happend on many other airports, or with other planes. p.s. Please, don't send me to hell. Quote Link to post Share on other sites
Goran_M 1,495 Posted Tuesday at 02:54 PM Report Share Posted Tuesday at 02:54 PM That's a really weird one. I've tested it and saw something in the log file that is likely causing the issue. I've sent my log file to Jim and he'll investigate. Quote Link to post Share on other sites
Suprex 1 Posted Tuesday at 04:17 PM Report Share Posted Tuesday at 04:17 PM Many thanks Goran. Quote Link to post Share on other sites
Babbo 0 Posted Wednesday at 07:22 AM Report Share Posted Wednesday at 07:22 AM 17 hours ago, JGregory said: If you map the condition levers to "PROP" then the default keys for prop adjust will work. Right, if you mean Prop coarse/fine a bit, this is already mapped by default to F3/4 - and it works nicely. However, it appears that detent-functionality then is ignored. Quote Link to post Share on other sites
BlazzerOne 4 Posted Wednesday at 08:24 AM Report Share Posted Wednesday at 08:24 AM I have some weird issues with the throttle. Before taking off I can move it with my hardware throttle the full range from reverse to full power however after touchdown I don‘t get them below flight idle. Quote Link to post Share on other sites
fINNPilot 0 Posted Wednesday at 08:34 AM Report Share Posted Wednesday at 08:34 AM you have to sync the throttle to with the TQ viewer all the time . That is unrealistic and makes the whole plane unplayable in vr. Will revert back to previous version. Quote Link to post Share on other sites
charraeus 0 Posted Wednesday at 10:35 AM Report Share Posted Wednesday at 10:35 AM Thank's a lot for this update! Quote Link to post Share on other sites
Suprex 1 Posted Wednesday at 10:42 AM Report Share Posted Wednesday at 10:42 AM Maybe it has already been written? but the CLIMB function execute the command but has no effect. Olso the captain altimeter does not work the arrow. Thanks for the attention. Quote Link to post Share on other sites
Vostflyer 0 Posted Wednesday at 12:27 PM Report Share Posted Wednesday at 12:27 PM (edited) 2 hours ago, Suprex said: Maybe it has already been written? but the CLIMB function execute the command but has no effect. Olso the captain altimeter does not work the arrow. Thanks for the attention. I just completed a flight and the Climb function worked for me. Note, I selected climb by simply mouse-clicking the Climb button on the mcp. If you are trying to use a joystick / TQ button or keyboard assignment, anything configured under the previous version will likely need to be re-assigned (search for ''les'' rather than 'LES' when looking for the commands). Edit, perhaps I have misinterpreted your post. I can only confirm the INITIAL Climb command worked (setting pitch to match target speed), since I transitioned to a different climb mode rather than trying to select the Climb M or Climb L settings. Edited Wednesday at 01:09 PM by Vostflyer Clarification Quote Link to post Share on other sites
Suprex 1 Posted Wednesday at 01:20 PM Report Share Posted Wednesday at 01:20 PM no, it doesn't work for me. I click in the button CLIMB, it changes M-L-H and the marker in the speed indicator, but not the speed and the VSI. I can only go up in IAS or VS mode. Quote Link to post Share on other sites
JGregory 243 Posted Wednesday at 01:56 PM Report Share Posted Wednesday at 01:56 PM 6 hours ago, Babbo said: Right, if you mean Prop coarse/fine a bit, this is already mapped by default to F3/4 - and it works nicely. However, it appears that detent-functionality then is ignored. Correct. Quote Link to post Share on other sites
JGregory 243 Posted Wednesday at 01:57 PM Report Share Posted Wednesday at 01:57 PM 5 hours ago, BlazzerOne said: I have some weird issues with the throttle. Before taking off I can move it with my hardware throttle the full range from reverse to full power however after touchdown I don‘t get them below flight idle. That means your hardware is out of sync with the manipulators. You can observe this using the TQ Viewer. Quote Link to post Share on other sites
JGregory 243 Posted Wednesday at 01:59 PM Report Share Posted Wednesday at 01:59 PM (edited) 3 hours ago, Suprex said: Maybe it has already been written? but the CLIMB function execute the command but has no effect. Olso the captain altimeter does not work the arrow. Thanks for the attention. 1 hour ago, Vostflyer said: Edit, perhaps I have misinterpreted your post. I can only confirm the INITIAL Climb command worked (setting pitch to match target speed), since I transitioned to a different climb mode rather than trying to select the Climb M or Climb L settings. Quote no, it doesn't work for me. I click in the button CLIMB, it changes M-L-H and the marker in the speed indicator, but not the speed and the VSI. Correct... there is a bug in the climb function and we are working on it. Edited Wednesday at 02:00 PM by JGregory Quote Link to post Share on other sites
BlazzerOne 4 Posted Wednesday at 05:15 PM Report Share Posted Wednesday at 05:15 PM 3 hours ago, JGregory said: That means your hardware is out of sync with the manipulators. You can observe this using the TQ Viewer. I checked it with the 2d panel of the throttle. I have a red line at flight idle wich stops the throttle to go below it. The green bars, which display my hardware throttle are already at full reverse however the throttle in the planes is still at flight idle. Quote Link to post Share on other sites
JGregory 243 Posted Wednesday at 09:42 PM Report Share Posted Wednesday at 09:42 PM 4 hours ago, BlazzerOne said: I checked it with the 2d panel of the throttle. I have a red line at flight idle wich stops the throttle to go below it. The green bars, which display my hardware throttle are already at full reverse however the throttle in the planes is still at flight idle. Exactly! Your hardware is NOT in sync with the manipulators. Move them so that the green boxes (your hardware) align with the yellow lines (the manipulators).. at which point they will sync and move together. Quote Link to post Share on other sites
Stef 0 Posted Wednesday at 10:40 PM Report Share Posted Wednesday at 10:40 PM (edited) On 2/23/2021 at 3:27 PM, Suprex said: I have a strange question for you: if I chose to place the Saab on one of these three airports (LFCI - LFCR - LFCK), X-Plane loading freezes on writing "Done with Pre-loading". This doesn't happend on many other airports, or with other planes. p.s. Please, don't send me to hell. I have similar issue. XPlane freeze on “building world” while placing the Saab on specific airport (LEBL with custom scenery). I didn’t make extensive test but it loads on LEMD for example. No problem with v1.5 or other aircrafts. Edited Wednesday at 10:46 PM by Stef Quote Link to post Share on other sites
Goran_M 1,495 Posted Wednesday at 11:42 PM Report Share Posted Wednesday at 11:42 PM 1 hour ago, Stef said: I have similar issue. XPlane freeze on “building world” while placing the Saab on specific airport (LEBL with custom scenery). I didn’t make extensive test but it loads on LEMD for example. No problem with v1.5 or other aircrafts. We're looking into this. I've run some tests and removed plugins, and it appears X-Plane gets caught in some kind of loop, and it only happens with the Saab, and only at specific airports. Still not sure what's doing this, but we'll get it fixed asap. Quote Link to post Share on other sites
Candid 0 Posted yesterday at 05:48 AM Report Share Posted yesterday at 05:48 AM The HDG slave button does not work for me in any mode. The course pointer is not positioned on the current flight path. It is also unclear how climb mode works. I have to climb in IAS mode. The rest of the model is like. Great work has been done and it has become pleasant to fly. Many thanks to the authors) Quote Link to post Share on other sites
Goran_M 1,495 Posted yesterday at 06:56 AM Report Share Posted yesterday at 06:56 AM 1 hour ago, Candid said: The HDG slave button does not work for me in any mode. The course pointer is not positioned on the current flight path. It is also unclear how climb mode works. I have to climb in IAS mode. The rest of the model is like. Great work has been done and it has become pleasant to fly. Many thanks to the authors) Point number 1. Quote Link to post Share on other sites
Candid 0 Posted yesterday at 11:21 AM Report Share Posted yesterday at 11:21 AM And I'm already writing about version 1.6 And I'm already writing about version 1.6 Quote Link to post Share on other sites
Candid 0 Posted yesterday at 11:23 AM Report Share Posted yesterday at 11:23 AM I updated to 1.6 and these are the bugs. The model itself is better, yes. Quote Link to post Share on other sites
Goran_M 1,495 Posted 23 hours ago Report Share Posted 23 hours ago 1 hour ago, Candid said: I updated to 1.6 and these are the bugs. The model itself is better, yes. Not sure if you understood the post. The HDG slave is not HDG sync...like some people believe. The heading slave function slaves the magnetic heading related to present flux detector readout. Since X-Plane now accurately simulates gyroscopic drift and flux_detector errors, HDG slave now functions correctly. Quote Link to post Share on other sites
Nandopiloto1985 0 Posted 7 hours ago Report Share Posted 7 hours ago On 2/22/2021 at 6:15 AM, Cristi said: I updated the airplane and I`m having an issue. I use the SAITEK QUADRANT THROTTLE. I move the throttle of my saitek quadrant and it doesn`t move the power levers from the airplane. I am so sad because I had no this issue. Quote Link to post Share on other sites
Suprex 1 Posted 1 hour ago Report Share Posted 1 hour ago Maybe that's not the right place for this question: where is the New V.2 of this wonderful work? Thank's. Quote Link to post Share on other sites
aeysim 0 Posted 58 minutes ago Report Share Posted 58 minutes ago (edited) It is very difficult to handle the nosewheel. Taxi is very difficult. Can't "noisewhell tiller" be assigned to this on joystick? In addition, it is very difficult to raise and lower the condition level arms. Can't you make it suitable for use with the joystick too? Edited 53 minutes ago by aeysim Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.