Goran_M

I don't have the Real Sim Gear setup, but I'm guessing you want 2 individually working PFD's. If this is the case, the default G1000, which is being used as a base to the G1000 in the TBM, doesn't allow for 2 separately working PFD's. SO what you get on 1 of them, is the same as what you get on the other one.

We rotated the ipad in the latest update to accomodate avitab users.

If it crashes again, please make a new forum post at the dedicated TBM 900 support section, along with your log.txt file.

Check any assignments in your hardware. Check maintenance manager for any damage to the reversers.

A blue shimmer is indicating that you're getting cold. A red one means you're getting hot. Take the appropriate steps. If it's hot, open the doors or turn on the AC. If it's cold, close the doors and turn on the heating.

Aircraft/X-Aviation/TBM-900/Documentation

A note for future reference, we'll see support posts in the relevant sections of the forums. There's a dedicated Saab forum further down. You're definitely not doing something right. Make sure controllers are calibrated and assignments are set. The chirping sound is the AP disconnect sound. This is turned off by pressing the Red button on the controls.

It's not something we even remotely looked at, due to the different sounds that would have to be played for a massive amount of different landing speeds/rates. We're talking about, literally, hundreds of different speeds and rates. I guess it's possible, but then performance might take a hit.

The way the G1000 is coded is definitely a question for Saso to answer. Feel free to ask him. https://discord.gg/EgX3V6

I don't have xcamera, so I can't comment on that, but the views are working fine on my end. Could there be some kind of conflict between xcamera and the default views? Check to make sure nothing else could be interfering. We didn't do anything to mess with the views in the TBM, so this is a strange one if you can't set your views.

There is an update in progress. We don't really have a blog, but we have a discord group. https://discord.gg/YUJ4MU

The rain on the glass is positioned that way so you cannot see any "clear" glass on the top edge where rain would normally be. It's done this way so rain can be seen from inside, running down the glass from above the glass edge. I'll look into the gear spray.

No. The charts are a PDF download into the display. The default G1000 doesn't allow the flexibility we would like to do what you're asking. The other option is avitab. We've integrated that into the ipad.

I'm empty. I've contacted Saso to jump in on this one, so maybe he'll catch something I might have missed.

This is the most bizarre problem I've seen on any add on. Again, your log file doesn't even show a crash or shut down. It just shows X-Plane quitting, without even a clean shut down. It just stops. Even when X-Plane is shut down properly, the log will state "X-Plane has shut down". One thing I did notice is that you're now running 11.4 b3. We don't really like working with beta's, but you did post logs from 11.36, so I can somewhat overlook that. However, seeing as you were finally able to load it, I'm starting to strongly suspect this is hardware related. It may sound a little out there, but are you able to download some software (your choice) to check your CPU and GPU temps? Also, it might be an idea to check your RAM. The easiest method is to use Windows built in RAM checker. Follow the steps here Try those suggestions and post back. Keep in mind, we're trying to eliminate possibilities, so I hope you don't mind going through some of these steps to help figure out what's going on.

Yeah, again, not even a crash or a clean shut down. It's like X-Plane is saying "Nah, I don't think so!" Time to try to dig a little deeper. I see scenery with ground traffic. Can you remove all 3rd party scenery? Even better would be to load up a clean X-Plane install with just the TBM, and no scenery, and then do a flight to see what happens. This is purely to isolate the problem. If it IS the scenery, it narrows it down for us, and we may be able to find something. The reason I think it MAY be the scenery is the TBM uses a very complex terrain radar, and if there is a corrupt scenery tile that the terrain radar tries to read, it will likely crash.

I don't want to go blaming other plugins, specifically...but that skunkcrafts updater has caused so many problem for so many people with the TBM. In cases like yours, when there is a very unusual crash, I would say 9 times out of 10, it was fixed when removing the skunkcrafts updater.

There's something else going on here that's confusing both Saso and myself. Like you say, the TBM isn't even fully loading, but this latest log file doesn't even show a crash. It just shows X-Plane stopping the load. I noticed you put all your plugins back. Can you remove them all and try again?

This one looks like a serious crash. Almost like it's rooted in Windows or even your RAM. I won't deduce anything at the moment, as it could be nothing serious. I've forwarded your log to Saso and I'll post back when he gives me his thoughts.

The selector will automatically switch at a predetermined time, regardless if the fuel cap is on or off. You might be surprised at how many people forget to replace the fuel caps after fueling. If it isn't the fuel cap, then check the integrity of the airfame through the maintenance manager. We've modelled wear and tear on the wing seams/joins, and fuel could be streaming out of the open/worn join (near the flap tracks).

Check your fuel caps are secured. It sounds like you were leaking fuel. (Yes, we simulated that, and you can actually see fuel streaming out of the opening at an accurate rate)

Check the circuit breakers and maintenance manager when something doesn't work.

Excellent. I did let Saso know about it. But I'll tell him all is good.

Did you turn on AP Trims?