Jump to content

JYW

Members
  • Posts

    15
  • Joined

  • Last visited

Everything posted by JYW

  1. The YD on the GFC700 autopilot is optional, and most SR20s of this age (and indeed the current model) don't come with the YD option on the GFC700. The SR22 always comes with GFC700+YD, and has an 'auto' setting above 200' AGL. You are right that the YD can still be engaged in the Torquesim G1000 SR20 (using key command). I think that is just a limitation of the Laminar G1000 software; YD seems to be always available. To fly the SR20 realistically, don't use the YD (as it's not available on the SR20 GFC700) and use rudder trim to get co-ordinated in the climb / cruise.
  2. Hi, I own the Torquesim SR22 G1000, SR20 Entegra (can't run this one due to severe performance stutters on my machine ), and yesterday bought the SR20 G1000. I know it's unrealistic, but I used Planemaker to change the SR20 to have nosewheel steering (my old pedals are just too twitchy for directional braking!). While in there, I noticed that the ACF file for the SR20 shows a power rating of 313hp? (The same as the SR22). Am I right in thinking that this value is not used by your simulation, as your engine modelling is custom? No issues with this, I'm literally just curious, as I was expecting to see 200hp there Cheers.
  3. Just found out about the release of this beauty. I am an existing SR22 G1000 owner (bought from X-Aviation), but did not receive any email with a discount code to buy the Entegra version.
  4. Hi, It's nice to see the A/C is modelled in the SR22. Just one area of feedback - there is no fan or blower sound at all when the fan is turned up. In the real SR22 the fan is very loud when on it's highest setting. It would be nice to see (or hear) this added. Thanks.
  5. Hi Sam, I was suffering constant CTDs, despite the Gizmo activation going ok and the licence being shown as activated. The solution that finally got me flying in the SR22 was to do the opposite of the advice, to load the Laminar C172 first. After several uninstall/reinstalls, when I finally tried for the first time to simply launch X-Plane and load the SR22 directly, it worked without issue. It seems the "Load the C172 first" advice isn't always the best route. Good luck. David @ EGNT
  6. You're lucky! Neither variant will load for me. It's hours since I bought this and haven't even seen a SR22 on my screen yet. No issues with activation (with the C172 loaded). The Gizmo Licencing screen shows the SR22 is activated, but as soon as I try to load either variant, I get a CTD. Very frustrating.
  7. Here is a screenshot, showing that the SR22 is activated in Gizmo. ......I've also tried re-updating the licenses. But as soon as I try to load the SR22, I get an instant CTD:-
  8. I have the same problem as Q8 Pilot and Pastrong, above. Instant CTD when loading the aircraft. Suggestions above have not resolved. Log attached. Log.txt
  9. The biggest thing that improved all aspects of ground handling (taxi and t/o roll) in the TBM for me, was setting "stability augmentation" on the yaw axis, completely off. I'd turned it on, assuming it would settle things down, but now understand the TBM was coded specifically for this value to be off. With it off, and by following these tips, I no longer have any issues; ground control is now perfect (and believe me, when I first tried the plane, it was absolutely awful!) - Rudder trim MUST be set, but not as far as the green area; about half way between neutral and the green area. - Calibrate your rudder pedals axis in your controller profile, before EVERY flight. - Introduce power very steadily on the take off roll (I usually take off with 85-90% torque). .....another optional tip that can settle the TBM's control sensitivity down, is to carry extra fuel.
  10. I will always do this from here forward! Hi Goran, yes, I've now managed to perform my first flight since purchase, by loading the C172 G1000 first, programming my FPL, then changing the the TBM. So very pleased it's the same issue as others have, and not performance related. (I had 50+ FPS - amazing!) Cheers.
  11. Thanks Dwight - with your help, I have been able to perform my first flight since purchase! I loaded a flight with the C172 G1000, programmed my entire flight plan (inc. PROCS), and then changed to the TBM. I was able to fly a full leg, although didn't dare try to make any FPL changes. Thanks, Bill
  12. I'm in exactly the same position James. Bought last night and not currently usable. But.... it's clear that it's not Hot Start's fault, but Laminar and their highly suspect release candidates as of late. Hopefully we'll be flying the TBM soon! ...identical point at which it crashes for me. Haven't even been able to hear my lovely engine yet!
  13. Hi, I temporarily installed my son's 1080 GPU this afternoon and turned every setting in XP11 to minimum. Same crash at the same point (engine start), so definitely not an out of memory.
  14. Hi Goran, Thanks - the plane does fully load up. It's only when I turn on the GPU or battery and the AHIRS starts aligning that the crash happens. FPS at this point are pretty high (40+FPS). Settings are already pretty modest but I'll try again with even lower settings. My GPU certainly is modest but manages with all other complex aircraft - I've never seen any crash like this before. If I was running out of memory, wouldn't this give a specific "out of memory" error message, rather than a run time error? I'll mess around with my settings but also await the update for the other compatibility issues between XP11.31 / 11.32 and the TBM. It's awful buying such a lovely aircraft and not having been able to use it all.
  15. Literally bought this product this evening, and get a Run Time Error within seconds of it loading. Although you can see the XP11 loading screen plane below, this is simply because XP11 launches again after the Runtime. The error occurs a few seconds after the TMB is loaded. Never had any crash or error like this in XP before. Gutted! Log.txt
×
×
  • Create New...