Goran_M Posted July 5, 2019 Report Posted July 5, 2019 You can post a log and I'll take a look. If you install a fresh copy of X-Plane, it will not install OrbX. OrbX has it's own installer. Quote
JackSwyr Posted July 5, 2019 Report Posted July 5, 2019 Just now, Goran_M said: You can post a log and I'll take a look. If you install a fresh copy of X-Plane, it will not install OrbX. OrbX has it's own installer. Where do I get this log? I just used the control panel in windows to uninstall. Then deleted the TBM folder. Now I’m installing it again. Then I’ll test it with my existing XP, if it doesn’t work then the next step is a new copy of XP. But how do I install two TBM’s in XP? One in each I mean? Quote
Goran_M Posted July 5, 2019 Report Posted July 5, 2019 (edited) log.txt is found in your root X-Plane folder When you install the 2nd TBM, just point the installer to the other X-Plane folder. Make sure the X-Plane folder is labelled differently or is on a different hard drive. Edited July 5, 2019 by Goran_M Quote
JackSwyr Posted July 5, 2019 Report Posted July 5, 2019 6 minutes ago, Goran_M said: log.txt is found in your root X-Plane folder When you install the 2nd TBM, just point the installer to the other X-Plane folder. Make sure the X-Plane folder is labelled differently or is on a different hard drive. Looks like I have no choice now. This is getting ridiculous. I reinstalled it and no matter what I do when I hit the starter switch that prop doesn’t budge. Not one thing has changed since last week, all I did was paint my office and come back to the same PC, and this PC is only for swimming, nothing else, ever. Will post the log in a few minutes and am going to try a new XP install. Quote
JackSwyr Posted July 5, 2019 Report Posted July 5, 2019 TBM900_Log.txt X-Plane Installer Log.txt Quote
RobW05 Posted July 5, 2019 Report Posted July 5, 2019 2 hours ago, JackSwyr said: All of a sudden it wouldn’t start so I uninstalled it and reinstalled it and still wouldn’t start till I used a GPU. And now I’m flying with CAS messages LOW VOLTAGE and MAIN GEN. But on the ground I had all like new. That is because you most likely left the source selector at "GPU" position instead of switching to "BATT" after disconnecting the GPU. Quote
JackSwyr Posted July 5, 2019 Report Posted July 5, 2019 1 minute ago, RobW05 said: That is because you most likely left the source selector at "GPU" position instead of switching to "BATT" after disconnecting the GPU. I never took it out of BATT though. Quote
Goran_M Posted July 5, 2019 Report Posted July 5, 2019 If the prop isn’t budging, it’s because you have no power going to the starter. Have you watched the included tutorial to make sure you haven’t missed a step? Quote
JackSwyr Posted July 5, 2019 Report Posted July 5, 2019 1 minute ago, Goran_M said: If the prop isn’t budging, it’s because you have no power going to the starter. Have you watched the included tutorial to make sure you haven’t missed a step? Yes, but I’ve started this plane a hundred times at least, it’s the only one I ever use in XP. I have a lot of real world experience with aircraft, this makes no sense at all. I’m finally able to install the TBM into the new fresh XP. Quote
JackSwyr Posted July 5, 2019 Report Posted July 5, 2019 2 hours ago, Goran_M said: You can post a log and I'll take a look. If you install a fresh copy of X-Plane, it will not install OrbX. OrbX has it's own installer. It works fine in the fresh install and works in the old one too. No idea what happened. No way they can be linked is there? Quote
Goran_M Posted July 5, 2019 Report Posted July 5, 2019 43 minutes ago, JackSwyr said: It works fine in the fresh install and works in the old one too. No idea what happened. No way they can be linked is there? No. They are not linked. 1 Quote
JackSwyr Posted July 5, 2019 Report Posted July 5, 2019 7 minutes ago, Goran_M said: No. They are not linked. Well, it’s working now. If I can only figure out how I got REV to work on my Virtual Fly TQ6, I’ve been messing with it and can’t for the life of me figure it out. Quote
Erich convair Posted July 5, 2019 Report Posted July 5, 2019 It happens to me few time too. I fixed it by deleting the states and recreated an airframe. 1 Quote
RobW05 Posted July 5, 2019 Report Posted July 5, 2019 4 hours ago, JackSwyr said: I never took it out of BATT though. It was just a guess, because you said you did start it with the GPU. 1 Quote
BigG_433 Posted July 5, 2019 Report Posted July 5, 2019 Just recently purchased this aircraft and experienced the same issue. NG temps were low but could not get ITT above 10%,. Twice I tried dry motoring for 10 seconds and immediately switching to abort with no success. Checked maintenance and found no issues there. As Erich states above, creating a new airframe resulted in a normal start. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.