All Activity

Sorry I should correct myself. Gizmo LTS seems to work except for level 2 activation when not using rosetta. All dials buttons and switches load and become interactive just no reactions from the interaction.

None of the systems can run without Gizmo. The entire aircraft system is written in it. It's not just activation. There will not be native ARM support for a while as we transition to C.

Is there any update for this? A beta or even an alpha with the notice that there will be bugs? There is a noticeable performance hit when translating x86_64 binaries and it seems most of the aircraft components are able to run natively except Gizmo for activation.

Can i get a new link sir many thanks

Yeah, the white area is the takeoff trim range. But, that doesn’t mean you should engage the AP with the trim there, if you are holding control pressure on the yoke, don’t expect the AP to take over seamlessly. The plane should be trimmed throughout the hand-flying phase of takeoff and initial climb, then with the plane in-trim, you can engage the AP when appropriate.

View File VP-BKM Hot Start Challenger 650 This is a livery for the Hot Start Challenger 650, inspired VP-BKM. To install, extract the zip file into the "liveries" folder. You can supply your own registration, VP-BKM is not printed on the stabilizer. If you enjoy my work, consider supporting me on Patreon to cover some of the horrendous Adobe-costs ;). Submitter pilotdeviation Submitted 05/15/2025 Category Hot Start Challenger 650  

Jurassic Park N293G X-Trident AW109 View File This is a livery for the X-Trident AW109, inspired by the AW109 from Jurassic Park. To install, extract the zip file into the "liveries" folder. This livery is in 4K. If you enjoy my work, consider supporting me on Patreon to cover some of the horrendous Adobe-costs ;). Submitter pilotdeviation Submitted 05/14/2025 Category Helicopters  

D-HHHH X-Trident AW109 View File This is a livery for the X-Trident AW109, inspired by D-HHHH. To install, extract the zip file into the "liveries" folder. This livery is in 4K. If you enjoy my work, consider supporting me on Patreon to cover some of the horrendous Adobe-costs ;). Submitter pilotdeviation Submitted 05/14/2025 Category Helicopters  

Thanks Coop!

Your antivirus deleted the plugin.

I have the same problem as everyone else where nothing works and gear is retracted... what should i do?? Here is the Log.TXT file attached below. Help is greatly appreciated. Thanks all Log.txt

ALT was always set to airport initial climb, so above the airport elevation. Speaking about trim, where can I find proper trim for departure? Meaning, is there any trim setting needed to be set per the TOW or something as such? I think the trim might be the case to be honest. Just have no idea how to properly set it up - resp. to which specific value, or it just have to be within the white area next to the trim wheel?

The STEC AP being used is the internal XP STEC. It is an incredibly dumb autopilot (as it is in the real world). It definitely is night and day in behaviors compared to modern APs (DFC90 with the Entegra, or anything Garmin, etc.)

With IAS mode, it should never descend even when trying to catch a selected airspeed, if the altitude preselector is above your current altitude (and vice-versa on descents). If it is that dramatic, then perhaps something maybe with trimming and your flight controls? VS is much simpler, much less logic going on, it is just targeting the selected VS. If its dramatically oscillating around that or diving before capture a positive VS then it sounds like your plane was not in trim before engaging AP.

When I start XP12, I get two popups: "X-aviation licensing. License expired. Please connect to the internet" and "License data invalid" I am connected to the the internet normally (no VPN). Log.txt

Hmmm. I'll try again later, but the preselect was not working for me. I know how to use this, but maybe I got something wrong yesterday... We'll see. No, IAS was not being used. It sort of followed the commanded VS, but it was not that accurate, and when well off the selected altitude, it was nowhere near right. Flies very nicely, but taxiing can be difficult. ------------------- I just tried it again. Started with engine running (saves time!), and it worked properly! Yes, it wanders about a bit from the assigned altitude, but that is expected and realistic, as the air is not static! It does correct itself. So, as to quite what was going on yesterday, I have no explanation. If it happens again, I'll send you a log file. Thanks for your interest :-)

The aircraft function is the same regardless of platform. Altitude pre-select should be followed so long as a vertical mode is active. This will ARM the pre-selected altitude. For VS, are you saying it will not obey a commanded higher pitch, or are you trying to use an IAS mode?

I have just upgraded to a Mac Studio, and run XP12 natively on the M processor (i.e. not Rosetta). I can't remember whether the stec-55x is supposed to have altitude preselect working on the Entegras - because my last Intel iMac couldn't run these planes without flashing screens, so I hardly used them, and stuck with the G1000s. Anyway, today, I found that altitude preselect (what I fed in on the Entegra PFD) was totally ignored by the autopilot. In fact, even the VS speeds were not kept to very accurately. Is this possibly a problem with the M processor? I had, earlier, tried the same plane in X-Plane 11 running in Rosetta, and the autopilot verged on being almost unusable for altitude control, and I gave up. I, so far, have had very limited experience in X-Plane using Mac Silicon, so I don't know what works, and what doesn't! I get super fps, which is a big plus.

Not super clean, but I think you'll get the idea...

Yes, I know. I have already done that. The funny thing is, I was sure I had mentioned this before, but I couldn't find any post from me about it, so I obviously hadn't. Thanks Cameron.

Hello there guys! Thanks for the great product you've created :-) I have an issue that is probably related to lack of my skill - so I need a bit of help on your side. Every time after departure when I engage YD, followed by AP aircraft starts to nosedive until it starts picking up speed again and climbing via IAS or VS. I thought it might "chase" IAS that is preselected but the same happens with VS selection. Anything I am doing wrong? Maybe the issue is the trim? Also I fail to find trim performance table, should there be any :-( Thanks a lot for your time.