Jump to content

Some small issues


Recommended Posts

Hello,

First of all, I just want to thank the IXEG Team for this beautiful 737 and for this recent update ! You are doing a great job, and with future updates, it will be even better !

I noticed some minor things that seem to be bugs to me and that I don't see on this forum, so I report them :

- Vortices appear very frequently unlike other similar aircraft I own, even with good weather.

802548462_B733-2020-05-2920_58_50.thumb.jpg.bcc8670d24f7945ec178c98d9f92009a.jpg

- When you start to descend and your thrust goes to idle, contrails start in front of aircraft :

- With mousewheel, on FLT ALT, when you decrease value and you go from 000 to 900, thousand value keeps the old value :

- On the FMC, after entering V1 / VR / V2, if you're going to Approach page, and then going for a second time to Takeoff page, values are reset. I don't know if this is a normal behaviour, but I don't have that on the Zibo for example.

That's all for me ! Hoping it will be useful. In any case, right now, I'm enjoying this bird, thank you again!

960049989_B733-2020-05-2920_13_53.thumb.jpg.5ebde799609083618453389222401611.jpg

Link to post
Share on other sites

Hi and thanks for the nice words and the feedback.

I totally agree about the vortices - we are using "default Laminar Research" particle effects for now - I really want to update those, though - and make better vortices (at the right spot and only the right conditions) and also APU heat blur, fire extinguisher bottle effects, better touchdown smoke, etc.

I also noticed the flight-altitude problem with the mousewheel, I will enter a ticket for Tom to look at it.

I am not sure about the Vspeeds - we may have coded this so that the take-off v-speeds get erazed from the EADI speed tape if you enter the approach speeds. I really don´t remember how the FMS handled this on the real 737-300, I never did that ;-) It is also quite possible that the behaviour was changed, I am sure the Zibo is using a much more modern software standard for their FMS.

Cheers, Jan

 

  • Like 2
Link to post
Share on other sites
29 minutes ago, Litjan said:

Hi and thanks for the nice words and the feedback.

I totally agree about the vortices - we are using "default Laminar Research" particle effects for now - I really want to update those, though - and make better vortices (at the right spot and only the right conditions) and also APU heat blur, fire extinguisher bottle effects, better touchdown smoke, etc.

I also noticed the flight-altitude problem with the mousewheel, I will enter a ticket for Tom to look at it.

I am not sure about the Vspeeds - we may have coded this so that the take-off v-speeds get erazed from the EADI speed tape if you enter the approach speeds. I really don´t remember how the FMS handled this on the real 737-300, I never did that ;-) It is also quite possible that the behaviour was changed, I am sure the Zibo is using a much more modern software standard for their FMS.

Cheers, Jan

 

Hi jan... I guess i have other issue here.

Is normal that the MCP IAS selection resets to 110 knots when i put online the gen bars from apu bar?... Is happening to me; i usually set v2 on mcp before push back and always it resets.

Link to post
Share on other sites

Hi,

Thanks Jan for your reply !

Custom particles effect can be a good addition. I didn't make the link until now but this behaviour is since XP particles update for both (11.30 I think).

For the Vspeeds I have found it randomly, when sometimes I click on the wrong LSK. After that I have tested on the zibo to see if behaviour is the same (only comparison I can do on my side). So I'll have to be more careful and click on the right LSK haha :lol:.

@Cptburgos I dont' have this problem on my side for information.

Link to post
Share on other sites
1 minute ago, Benj said:

Hi,

Thanks Jan for your reply !

Custom particles effect can be a good addition. I didn't make the link until now but this behaviour is since XP particles update for both (11.30 I think).

For the Vspeeds I have found it randomly, when sometimes I click on the wrong LSK. After that I have tested on the zibo to see if behaviour is the same (only comparison I can do on my side). So I'll have to be more careful and click on the right LSK haha :lol:.

@Cptburgos I dont' have this problem on my side for information.

That is weird, let me make a video

Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
  • Recently Browsing   0 members

    No registered users viewing this page.

×
×
  • Create New...