kjhkent

Thanks for the correction.

Make sure that the red manual overide lever is fully forward.

I know. Not expected.

Just a heads up. I appreciate its a beta but 11.30b2 breaks the TBM. It will load but the side buttons for air frame, maintainence etc are all over the place and not easilly selectable. I am reverting back to 11.30 b1 where I personally had very few issues.

I thought it was a good response ?

Today as it was wet and unpleasant I decided to do a flight from Southend to Bilbao. Took off and climbed to 22000 with no issues at. After about 200 nm I noticed that all the glass displays became unclear almost as if sunlight was reflecting off them. However when I clicked on each display it maximised and was clear and bright. Eventually each display became unreadable as if white out. When maximised each display was black. Eventually all the electrics shut down and eventually crashed. Otherwise the cockpit was clear so not it would appear oxygen related. Any ideas would be appreciated.

Thanks.

Had a couple of flights without any issues.

I have noticed in some videos that the Hotstart TBM900 is shown with an ipad mounted on the yoke. Is this standard in which case how do you get this. If not what add on is it ?

I have never got such immediate help from the developers as I have with this aircraft. Will buy from them and Xaviation again.

All resolved the manual overide lever was not fully back.

Have now been flying all morning and getting to grips with the aircraft properly. Thanks again

Also great response from Cameron. Thanks.

I see version 1.08 is out. Fantastic support from the developers.

Hopefully all will be well when I get back to it tomorrow. Thanks very much for the time you have taken to help.

skiselkov The lever was not fully down. Started procedure again and suffered immediate engine fire. Back into maintainence and again repaired Turbos and Combustor again. Changed livery. Tried again. Engine fire. Repaired again and the emgine started as in tutorial. I have now shut down and restarted 4 times without a problem. Also short flight and landed. Shut down. Waited 10 minutes and restarted again without a glitch save a warning that the ngine was still hot. Backed off to idle. ITT fel nicely and was able to do another short flight. Totally baffled save that the red lever was not fully down as stated. Will shutdown xplane tonight and try again tomorrow. I will report back. Very grateful for your advice and time.

On to it now.

Will do. These two items fail immediatley during the startup procedure, even with a new airframe. I get a warning as soon as I move the battery to the on position that the engine is too hot. Repair combustor. Engine starts and shuts down. Then intermitently the engine will be running on startup and or with an engine fire and smoke.

skiselkov Thanks for the response. Baffled by this. Log.txt

Yes done that. No joy.

Having now downloaded and installed this aircraft ver 1.07, I find that the engine is already running with no instruments displayed and black smoke emmitting from the engine cowling. The maintainence tab shows engine faults in turbine and combustor which I am unable to repair or clear. Very disappointed. Posted on varoius forums but can seem to find no central avenue for support.

So today I downloaded version 1.07. When I load the plane the engine is running and on fire. I can now open maintenance and see that the turbine is damage and I am unable to repair the Combustor. I am following the Tutorials and know the procedures but the engine is already on fire as soon as I load it. I have attached my Log.txt. Is there someone that could make any sense out of this. I am unable to reload the aircraft in a new condition and whatever I do now the engine is running and alight. Thanks in advance and for your patience. I am using an i7 Imac with a 4gb graphics card. Using os10.14 Log.txt

Thankful to see your post. I use a Mac and have the exact same issue.

ITT is not above 150. With throttle at low idle there is no increase at all in NGT. In the tutorial where it says wait for NGT to increase it stays at 0. I also get the fire warning before adding fuel during the pre start procedure. The tutorial does not start engine either.

Further to my earlier post. I now see that during the startup process I get a fire warning and smoke emits from the engine compartment.