B737

Thank you, very very good explanation. Promising the last of the year. ! I have attached one old fashion panel. on this where would you set the xponder for taxi? Am I right, that in this case the alt should be off ( as in the picture, center )

Thank you Jan ! Just 2 more in this topics. On newer atc mode panel we have alt select to off. What is the reason? 2. Tcas panel has above and below. When and why do we have to use?

Dear all! I need a bit help in relation of transponder usage. Taxi, line up and tcas settings. Thank you.

Hi everybody! I am bit new with ixeg transponder. I need help. So I can not find switch to deselect the alt function for gnd taxi. Can somebody pls help me when and how to use all swicthes on that panel. I meant taxi, flight, tcas....etc

Thank you! Sounds like bit better to take more fuel than required by flight plan to get more margin.

1.In real life when we getting the operational flight plan does it contain the wind calculation in relation to determine the minimum fuel required or not? 2. If we can not reach the destination without using the reserve what should we do?

Dear Jan! Thank you. Which procedure is used in performance chart? Static or the 40%? Question is: I know in the real life is much more difference, but playing in games when the table tells you need 1500 meters for take off and the runway is 1500m. I am not sure that both of the procedures would work.

Dear all! When we get the result for take off run via performance table or app how it is calculated in relation with thrust and brake setting? 1. Full thrust and brake released when spinned up? Or 2. Brake release, set 40% N1 and after 40% set take off thrust? Because from my view it can be significant difference. Can' t be? Regards

Dear Everybody! I need help about understanding fuel penalties. Picture attached. Hard to understand for me. Thanks

Thank you!

Thank you very much. I was thinking about wind also, due to fmc does not get wind data ahead.....

Dear Jan! I need help, possibly piloting issue. Almost every time the fmc can not calculate the route without ,,required drag'' message. Most of the time the A/ P can not handle the speed and vertical speed in the descent phase and usually overshooting everything even we can not capture the glide slope due to we still high enough with overspeed. Where can I be wrong?

Shall I use A/T and/ or A/ P when doing your test? How did you do exactly? Marginal effect for me is only at the moment when N1 increasing and the G/ S reducing just a little. IAS almost remain constant But when comparing ixeg with other aircrafts in xplane the difference is quite big in drag. I did not say you are not right, but not easy accept or detecting deceleration....

Wilco. Thank you

Agree with your reply due to you do not have access to aircraft mechanics documents. On b737 classics a/ t can not move one lever in air when you switch off one engine. Lever angles compared.... But it works as I said. On those wide body aircraft where you have seperate A/ T switches there you will have A/ T seperately. On Airbus you will always have A/ T on the remaining engine in case of failure

Bites somewhere collapsed in my side. Answer accepted, sorry.

Answer accepted. Thank you. Looks like you were right !

Thank you, do not forget I am at your side. I love so much this sim honestly :)! On of the best in the market! At least getting feedback where and which side is the problem.

Agree and nice to know. Thank you. Back to our original topics, the A/ T should not let to engage the system, when one engine failed with throttle at idle stop on the side of the bad engine

Thank you, in this case the fault in my computer& side

Will check, thank you

Actually I try in descent mode by V/S. Choose the V/S high enough just to let the throttle at idle by A/T. After all of these settings try to extend the spoiler and pls let me know what you saw. Pls check this, and will see surely what I am talking about. Zero effect

Windmilling start: I did a fast decent dive to go above 260knots, I set the start switch to flight position and selecting start lever to idle

Dear Support! I would like to get clear answers. I am reporting real bugs with details which are can be very easily checked back less than a minutes. As a gift I was blocked for 10 hours I am really not sure who is taking effort for checking back or getting contacts with the developers or It section of ixeg at least try to fix the bugs. I am in aviation since 2002 with B737/cl,ng, max A320/21 licences with real documents... This sim is one of the best in the market and it would be our common goal to make it better more. Who' s taking decision to which bugs are transferred to the developers? From my view it sounds like this bug report forum is for just calming down the customers...