divinglyc

Thanks! I think it works for me!!

Thanks a lot! Today I sucessfully did a VOR landing following your instruction.. However, I have a question... It seemed that I didn't have to set VS to descend because VNAV automatically shifted to VGP and descend by itself?

This happens to me sometimes... no idea why..

Ah!! Really made a mistake! Thanks so much for clarifying! I will try that later!!

Thank you so much for your explanation! I have a question...... If I use BRG SRC to show the VOR needle, how can I leave the Navigation source in FMS1 mode? Or do you mean I use Format to change it to VOR mode and leave the BRG SRC at FMS1? Sorry for my confusion....

Hi! I was flying to LGSR with VOR rwy 15 landing. I have activated APPR mode, Nav mode, VNAV mode. I have also shift my Navigation source to VOR1 which has been set to the correct frequency and course. However, how can I make the aircraft follow the correct path to descend? Thanks! ps. In the end, I manually and visually landed.

I also have this confusion in mind for a period of time. And seems it happened only when you are close to TOD.. In the beginning of the flight, the ETA seemed correct.

Thank you so much. So here is what I think I should do.. I enter the pax number and weight and also the cargo weight in the FMS. Then I enter the sum of the above weight into the payload of the XP weight/balance interface. As to fuel, I only enter that in the FMS. Is that correct? )The reason I enter pax/cargo/fuel in the FMS is for the FMS to calculate Vspeed.)

Hi! I am a little bit confused. I fly non-career mode most of the time( in fact that's only 3 flights so far ). I enter the Pax number, weight and cargo weight in the FMS. The FMS would calculate a ZFW for me. However, when I check the XP weight/balance setting page, the ZFW is not the same as that in the FMS. So in the end, should I make any adjustment in the XP weight/balance page? If I leave it alone, would the plane load it self according the numer I entered in the FMS?(including the fuel wight). Or should I enter the weight anywhere in the sim to make it actually take effect? Thanks a lot.

After reading the materials, I have learned a lot! Thanks!

Hi! When setting the FMS, I got a negative "P ALT" in the Takeoff Ref page. I have set the QNH and Temp accordint to the ATIS..so what might I have missed? Thanks!

Thanks a lot!

Thanks! What if I fly the non-FBO type? Do I have to edit the X plane Weight/balance?

Hi! I have question. When loading the aircraft, do we just fill in the pax number/cargo/fuel weight in the FMS( ACT PERF INIT page)? Should we also fill in the weight in the X plane Edit Weight/balance page? Thanks!

Hi! If I don't fly the career mode, thena tank would not show up and I wouldn't know the density of the fuel. How do I calculate the liters amount? Thanks!

Thanks a lot! I will have a closer look.. maybe I have missed it....

Thanks for this brilliant airplane! I have been learning it step by step by the stream videos and manual (by checklists, too) I have a question for so far... How can I calculate the ToD point? It's not in the FMS.. so is there a specific way to calculate it during flight? Thanks!

Thanks! I got it! It's the command "Disco Servos"

Hi! If I want to assign a key or joystick button to the function of AP disconnect(the red buttone on the yoker), which command should I use? I cannot find it in the setiing page. Thanks a lot!

Thanks! I will try that out!

No, if I disable xEnviro, it goes away. Also, is I run X plan in OpenGl, not in Vulkan, it goes away.

Hi! I have the latest version of TBM900, xEnviro and XP11. My GPU driver is also updated (AMD 5800XT). However, when I load the TBM in Vulkan with xEnviro activated, the whole screen flickers intermittently. If I disable xEnviro or if I used OpenGL, the flickering disappeared. And if I change to other aircrafts, this does not happen either. Does anyone experience the same thing and is there anything I can do? Thanks!

Oh! I see! Thanks a lot!!

H! Have you found it yet? Thanks a lot!!

Thank you so much!!!