[I can't assign autopilot disconnect command to my yoke controls]

I will try

Thanks

[I can't assign autopilot disconnect command to my yoke controls]

Hi,

I am unable to assign this command “xscenery/mu2b60/autopilot_disconnect“ to my yoke commands.
In don't find the command on XP settings joystick and if I use xsaitekpanels.ini that don't work too.
May be, I do somyhing wrong.
If somme one could help me it will be great.
Thanks by advance

Pierre

[How to adjust screen brightness.]

Too bad
Anyway thanks for your answer

[How to adjust screen brightness.]

It should be a stupid question  but I didn't find how to adjust brightness of the two screens of the G1000 avionics.
Thanks by advance for you help.
Pierre.

[Take Command! IXEG 737 Classic v1.21 Update Released!]

In case of it could help someone.

Since I updated to v 1.21 I had the same Gizmo console alert as Captain_Crow and some other. I removed all my plugins but nothing changed. To solve this problem the only solution I found it's to at first open XP, load the 733, quit XP and reopen it. By this way evrything work well. So it's only when I open XP with an other plane and I load the 733 that i have this alert.

Pierre

[Unable to fly more than 10 mn]

That's it  I did my first flight.
Thanks alot for your help. That was xsaitekpanels which make XP crash, i had the wrong version compare to .ini file. But above all I mad some mistake when I create my xsaitekpanels.ini file, I rewrote a simple new one this night and everything does Ok.
Thank again for this wonderful bird and the X-Pilot comunity.

[Unable to fly more than 10 mn]

Thanks you for your so quick answer. I'll try this tonight and I'll tell you.

[Unable to fly more than 10 mn]

I should say I am very frustrated. Your plane look so amazing and you did a wonderful job, but unfortunately, after 1 week, I never flew more then 10 mn.

In fact, after loading the 737, whatever I do X-Plane crash after 5 to 10 mn. Even I try to reproduce the Tutotial Flight 4 or I try to fly from other airports I have the same problem. XP always crash, but not at the same time. Som time It's when I completed the FMS, sometime during taxi or, when I'm luky, it's during climb. I tried to fly with and without my plugins, from several airport, with different flight plans but without success. I am aware that my explanation are confuse but I have no more detail. I didn't notice any specific action that make XP crashing, it's like it was just a question of time. XP crash always in the same way, after several minutes all the 737 screen goes black and XP shut off.

I have several other planes which fly without problem. If you have any solutions i will be very happy 

Log.txt

[CRJ200 Autopilot and NAV issue]

burgnon

 

It's look like you forget to insert a SID. Try to begin your fly with a SID or use at first the HDG mode with NAV mode engage to intercept your route.

 

Pierre

[CRJ-200 swing at high speed on runway]

I tried 2 and 3 but nothing changed.

 

Pierre.

[CRJ-200 swing at high speed on runway]

No cross wind. The CRJ swing even i select CAVOK.

It's like a problem of stability.

I will try to make a video.

 

Pierre

[CRJ-200 swing at high speed on runway]

First of all thank for your post and sorry for the delay of my answers.

 

BWolf7 : To be more precise the nose moving up to down it's like i have a problem with a damper  .

cessna729 : i'm using a separate rudder.

 

Pierre

[CRJ-200 swing at high speed on runway]

Since i flight the CRJ on XP 10.21 32bt I noticed that the plane swing alot at high speed on runway (above around 100 Kts) when i takeoff and when i land. It's very unpleasant and i would like to know if theire is a solution to reduce it.

 

Thank by advance for your answer.

 

Pierre

[X-plane crash when i switch on electrical power]

i flight !!!!

i find a strange solution for my problem.

First i  load the Dash 8 Q400 from ARMCHAIRAVIATION (a other great plane but not as great as yours of course  ) which use GIZMO, i reboot scripts in GIZMO PLUGIN menu after i load the CRJ and everything is OK !!!!!!

Just a other question, when i takeoff the plane turn to the right thus I have to compensate with the york. I would like to know if it's normal or if i miss somethings when i start the plane.

Thanks for your job !!

Pierre

Log.txt

[X-plane crash when i switch on electrical power]

Hi,

i installed the 1.1.1 update of CRJ and everything was ok. i made some fly but suddenly i could not start the CRJ any more.

I put battery on, i start GPU and when i click on AC button X-Plane crash. I have the same problem when i try to start whit the APU. I can start the APU but when i turn on the APU GEN X-plane crash. It's like XP crash when the PFD and MFD screen switch on.

i reinstall several time the CRJ, i removed all my plugin, i removed all XP preferences but I was never able to re-fly  ???

If you have any subjection, i will be very happy to fly again this great plane.

Pierre

Log.txt

crash_log.txt

[[SOLVED] Problem with speed mode in IAS or MACH]

i did, my be to fast.

When it's written “Speed mode is displayed in either IAS or MACH.“ I thought that we could select the speed either IAS or MACH.

Sorry for my misunderstanding.

Pierre

[[SOLVED] Problem with speed mode in IAS or MACH]

Hi

When i clic on the speed knob the speed mode doesn't change in MACH, it's stay in IAS.  ??

When i climb, after M 0,68 i have to change manually the speed to maintain the MACH airspeed.

Pierre

[XPSaitek plugin crash]

I have the same problem with XPSaitek plugin for windows. Specially with the Multipanel (Autopilot) and the Switchpanel.

For the Multipanel it could be a problem with the pitch trim and the ATH switch.

It's not a Saitek plugin but the one developed by floegl that you can find here : http://forums.x-plane.org/index.php?app=downloads&showfile=10161.

Any way, congratulation for your great job on this wonderful plane;

Pierre